欢迎您访问莱州聚峰机械有限公司网站!
搅拌机行业持续先行者!
点击拨打服务热线:400-879-1999
您的位置: 首页 > 新闻资讯搅拌车离合器不分离怎么办

新闻资讯

产品

新闻

  • 小型搅拌机的正确操控有哪些要求
  • 搅拌机使用时4大“控制”达到目的
  • 混凝土搅拌机检修的方法有哪些
  • 小型搅拌机零件气门的顺利使用方式
  • 混凝土搅拌机的操作保养关注事项
  • 什么原因导致搅拌机存在抱轴问题

全国服务热线

400-879-1999
新闻资讯 /

搅拌车离合器不分离怎么办

来源:http://www.zkhntjbc.com/ 日期:2021-11-17
概述:离合器不分离原因及方法一Causes of clutch non separation and solutions I你要先检查下离合油壳里的刹车油是否够用,如果
离合器不分离原因及方法一
Causes of clutch non separation and solutions I
你要先检查下离合油壳里的刹车油是否够用,如果油不够,离合怎么可能会生效?如果油量检查正常,那么先上车多踩几脚离合,看是否挂档有,那么是因为离合油路中存在空气,先排空气再试试。
First of all, you should check whether the brake oil in the clutch oil shell is enough. If the oil is not enough, how can the clutch take effect? If the oil quantity is normal, step on the clutch first to see if it is in gear. It is because there is air in the clutch oil circuit. Exhaust the air first and try again.
离合器不分离原因及方法二
Causes and solutions of clutch non separation II
如果油够的活,请检查离合总泵、离合分泵四周有无漏油现象,如果有漏油,在不考虑维修,只单单考虑问题的情况下,更换漏油的分泵或总泵处理。
自动混凝土搅拌机
If there is enough oil, please check whether there is oil leakage around the clutch master cylinder and clutch slave cylinder. If there is oil leakage, replace the leaking slave cylinder or master cylinder without considering maintenance and only considering solving the problem.
离合器不分离原因及方法三
Causes and solutions of clutch non separation III
更换好漏油的总泵或分泵后,再次给离合总泵处的油壳加入刹车油;再找另外一人帮你起动一面猛踩离合踩到次数踩住不放,另一个人在下面排空气,排完后锁紧空气螺丝,再重复上述流程,直到排到离合感觉高起来,放空气螺丝放不出气泡出来为止。锁紧放空气螺丝,同时检查离合分泵及总泵两者的分享推杆的自由间隙,一般为两到三毫米左右,手感有点间隙则可。
After replacing the leaking master cylinder or slave cylinder, add brake oil to the oil shell at the clutch master cylinder again; Find another person to help you start, step on the clutch and hold it for several times, and another person will exhaust the air below. After that, lock the air screw, and then repeat the above process until the clutch feels high and the air screw can't release bubbles. Lock the air release screw and check the free clearance of the shared push rod of the clutch slave cylinder and master cylinder at the same time, which is generally about 2-3mm. If there is a little clearance, it can be.

截屏,微信识别二维码