如欲使搅拌机正常工作、延长使用寿命，就要遵守相关的各款原则以及操作准备，下面混凝土搅拌机厂家就来讲讲吧。

If you want to make the mixer work normally and prolong its service life, you must abide by the relevant principles and operation preparation. The concrete mixer manufacturer will talk about it below.

(1)在驾驶室内操纵操作手柄时，请勿踩踏加速踏板。

(1) Do not step on the accelerator pedal when operating the joystick in the cab.

(2)搅拌机行驶时，操作手柄应置于“搅动”档内，驾驶室内的防逆手柄亦应加以锁定。如操作手柄仍置于“进料、搅拌”档内，则会降低预拌混凝土的质量，影响搅拌机的行驶性能。

(2) When the mixer is running, the operating handle should be placed in the "stirring" gear, and the anti reverse handle in the cab should also be locked. If the operating handle is still in the "feeding and mixing" position, the quality of ready mixed concrete will be reduced and the driving performance of the mixer will be affected.

(3)搅拌机开始工作前，发动机应空转预热。

(3) Before the mixer starts working, the engine shall be idled and preheated.

(4)扳动操作手柄时，切勿用力过猛。

(4) Do not pull the operating handle too hard.

行驶前的安全准备工作：

Safety preparation before driving:

车辆行驶前，应做好下列准备工作：

Before driving, the following preparations should be made:

(1) 将操作手柄扳至“搅动”位置，使拌筒以搅动速度回转。

(1) Turn the operating handle to the "stirring" position to rotate the mixing drum at the stirring speed.

(2) 将驾驶室内推拉软轴操作手柄卡在定位块的槽中锁定。

(2) Lock the push-pull flexible shaft operating handle in the cab in the slot of the positioning block.

(3) 检查卸料槽锁柄是否扣牢。

(3) Check whether the lock handle of the discharge chute is fastened.

此外混凝土搅拌机出车前的作业检查：

In addition, the operation inspection before the concrete mixer is set out:

检查时如发现异常现象，应找出原因并排除之。

If any abnormal phenomenon is found during inspection, find out the cause and eliminate it.

检查部位：

Inspection position:

发动机起动前

Before starting the engine

减速机、柱塞泵润滑油有无渗漏

Check whether the lubricating oil of reducer and plunger pump leaks

拌筒操纵装置的操作手柄应置于空档位置。

The operating handle of the mixing drum control device should be placed in the neutral position.

注意：如拌筒和发动机同时起动旋转，则有可能发生危险。务必注意!

Note: if the mixing drum and the engine start and rotate at the same time, there may be danger. Be careful!

发动机预热时

During engine warm-up

变量泵、马达是否有异常

Whether the variable displacement pump and motor are abnormal

减 速 机是否有异常

Whether the reducer is abnormal

操作位置(发动机预热后)拌筒的进料回转和出料回转是否正常,能否正常地进行回转

Whether the feeding rotation and discharging rotation of the mixing drum at the operating position (after the engine is preheated) are normal and whether they can rotate normally

驾驶室内锁紧杆是否锁紧

Whether the locking lever in the cab is locked

大家要注意检查时，切忌用手碰触机器的转动部分。并注意勿使衣服被机器卷入，安全是重要的，更多事项了解就来我们网站http://www.zkhntjbc.com看看吧。

Please note that during inspection, do not touch the rotating parts of the machine with your hands. And pay attention not to let the clothes be involved by the machine. Safety is important. Come to our website for more information http://www.zkhntjbc.com Take a look.