自动混凝土搅拌机常见故障有搅拌轴闷车、搅拌时产生异响、减速箱噪音严重、减速箱温度过高、搅拌罐两端轴温度过高、轴端漏浆。那么，常见故障的原因是什么呢?下面本文就具体为大家进行介绍。

The common faults of automatic concrete mixer include: the mixing shaft is blocked, abnormal noise is generated during mixing, the noise of reducer is serious, the temperature of reducer is too high, the temperature of shafts at both ends of the mixing tank is too high, and the shaft end leaks slurry. What are the causes of common failures? This article will introduce you in detail.

常见故障一:搅拌轴闷车

Common fault I: the mixer shaft is stuck

1、严重超载,这时需要重新调整进料质量,卸出多余物料;

1. In case of serious overloading, it is necessary to readjust the feeding quality and unload the excess materials;

2、自动混凝土搅拌机搅拌叶片或侧叶片与罐内壁间有大的异物,这时需要人工排除异物并重新调整间隙;

2. There is a large foreign matter between the mixing blade or side blade of the automatic concrete mixer and the inner wall of the tank. At this time, it is necessary to manually remove the foreign matter and readjust the gap;

3、电机皮带过松,这时需要调整紧张装置,拉紧皮带。

3. The motor belt is too loose. At this time, the tension device needs to be adjusted to tighten the belt.

常见故障二:搅拌时产生异响

Common fault 2: Abnormal noise during mixing

叶片或端刮板与罐内壁间隙过大,这时需要调整间隙到规定要求;

The clearance between the blade or end scraper and the inner wall of the tank is too large, so the clearance needs to be adjusted to the specified requirements;

常见故障三:减速箱噪音严重

Common fault 3: the gearbox is noisy

箱内有异物,这时候需要异物,修理或将损坏零件换新;

If there is foreign matter in the box, it is necessary to remove the foreign matter, repair or replace the damaged parts;

轴承损坏,这时需要换新的轴承。

The bearing is damaged and needs to be replaced.

常见故障四:减速箱温度过高

Common fault 4: The gearbox temperature is too high

油的粘度过高或过低,这时需要将油放出,补充新油;

If the viscosity of oil is too high or too low, it is necessary to drain the oil and replenish new oil;

轴承损坏,这时需要换新轴承。

The bearing is damaged and needs to be replaced.

常见故障五:搅拌罐两端轴温度过高

Common fault 5: The shaft temperature at both ends of the mixing tank is too high

自动混凝土搅拌机的轴承损坏,这时需要换新的轴承;

The bearing of the automatic concrete mixer is damaged and needs to be replaced;

供油量不足,这时需要按规定要求家注润滑油。

In case of insufficient oil supply, lubricating oil shall be injected as required.

常见故障六:轴端漏浆

Common fault 6: slurry leakage at shaft end

浮动密封损坏,这时需要换新浮动密封。

The floating seal is damaged and needs to be replaced.

导致自动混凝土搅拌机使用出现6个故障的原因就讲解到这里，提前了解到问题就能提前进行处理预防，才能保障人身以及施工质量，更多相关信息的了解就来我们网站http://www.zkhntjbc.com看看吧！

Here are the reasons for six failures in the use of automatic concrete mixer. If you know the problems in advance, you can deal with them, solve them and prevent them in advance, so as to ensure personal safety and construction quality. For more information, please come to our website http://www.zkhntjbc.com Look!