欢迎您访问莱州聚峰机械有限公司网站!
搅拌机行业持续先行者!
点击拨打服务热线:400-879-1999
您的位置: 首页 > 技术服务按这个程序操作小型搅拌机简单易懂

技术服务

产品

新闻

  • 小型搅拌机的正确操控有哪些要求
  • 搅拌机使用时4大“控制”达到目的
  • 混凝土搅拌机检修的方法有哪些
  • 小型搅拌机零件气门的顺利使用方式
  • 混凝土搅拌机的操作保养关注事项
  • 什么原因导致搅拌机存在抱轴问题

全国服务热线

400-879-1999
技术服务 /

按这个程序操作小型搅拌机简单易懂

来源:http://www.zkhntjbc.com/ 日期:2022-12-21
概述:小型搅拌机是把水泥、砂石骨料和水混合并拌制成混凝土混合料的机械。主要由拌筒、加料和卸料机构、供水系统、原动机、传动机构、机架和支承
小型搅拌机是把水泥、砂石骨料和水混合并拌制成混凝土混合料的机械。主要由拌筒、加料和卸料机构、供水系统、原动机、传动机构、机架和支承装置等组成。小编在这里提醒你,按这个程序操作小型搅拌机简单易懂!
Small mixer is a machine that mixes cement, sand aggregate and water into concrete mixture. It is mainly composed of mixing drum, feeding and unloading mechanism, water supply system, prime mover, transmission mechanism, frame and supporting device. Xiao Bian is here to remind you that it is easy to understand how to operate a small blender according to this procedure!
安装:
Installation:
机器拆箱后应检查减速机,料筒,轴承座,再运输中有无损坏,坚固件有无松动若有松动应拧紧,支撑地基为平整混凝土地面,搅拌机搬运时应用绳索系再机架上,不可套系在搅拌轴上,搅拌机底座下面安装有脚轮,可任意移动。
After the machine is unpacked, check whether the reducer, barrel, bearing seat are damaged during transportation, and if the fasteners are loose, tighten them. The supporting foundation is flat concrete ground. When the mixer is transported, it should be tied to the frame with ropes, not tied to the mixing shaft. Casters are installed below the mixer base, which can be moved freely.
操作程序:
Operating procedures:
1、启动前先检查旋转部分与料筒是否有刮碰现象,如有刮碰现象应及时调整。
1. Before starting, check whether there is any scratch between the rotating part and the barrel. If there is any scratch, adjust it in time.
2、清理料桶内的杂物。
2. Clean the sundries in the bucket.
小型搅拌机
3、启动前应将筒体限位方能启动。
3. The cylinder shall be limited before starting.
4、搅拌轴旋转方向应按筒体端面标记所示。
4. The rotation direction of the mixing shaft shall be as shown in the end face mark of the cylinder.
5、装入的混凝土物料必/须清/除金属或其/他杂物。
5. The loaded concrete materials must be cleaned of metal or other sundries.
6、根据搅拌时间调整搅拌器的定时,注意必/须在断电的情况下调整
6. Adjust the timing of the mixer according to the mixing time, and pay attention to that it must be adjusted when the power is off
7、按动启动按钮,主轴便带动搅拌铲运转。
7. Press the start button, and the spindle will drive the mixing shovel to run.
8、达到调定时间后自动停车。
8. Automatic stop when the set time is reached.
9、卸料时应先停机,打开/锁定销,搬动手柄使料筒旋转到一定位置,使紧销定位旋转主轴,使拌合料排出筒外。
9. When discharging, stop the machine first, open/lock the pin, move the handle to make the barrel rotate to a certain position, make the locking pin locate and rotate the spindle, so that the mixture can be discharged from the barrel.
10、拌合料排净后手动使筒体复位,将搅拌筒用锁定销定位。
10. After the mixture is discharged, manually reset the cylinder and position the mixing cylinder with a locking pin.
11、清洗料筒可将水倒入料筒内,使主轴旋转进行清洗,也可用干砂清洗。
11. Water can be poured into the material barrel to make the spindle rotate for cleaning, or dry sand can be used for cleaning.
按这个程序操作小型搅拌机能更好更顺利的进行工作,当然您要提前做好问题的预防工作,防止故障发生影响设备的完好以及工作的高质量,更多相关注意事项就来我们网站http://www.zkhntjbc.com咨询吧!
The operation of small mixers according to this procedure can be better and more smooth. Of course, you should prevent problems in advance to prevent failures from affecting the integrity of the equipment and the high quality of work. More relevant precautions can be found on our website http://www.zkhntjbc.com Consult!

截屏,微信识别二维码