欢迎您访问莱州中科聚峰机械有限公司网站!
搅拌机行业持续领跑者!
点击拨打服务热线:15053524111
您的位置: 首页 > 新闻资讯>>3.5方搅拌机发动机运行错误有什么影响?

新闻资讯

热销产品

推荐新闻

  • 安全使用规范是什么?
  • 聚峰混凝土搅拌车,您的选择!
  • 高效作业的前提:即正确使用混凝土搅拌车
  • 聚峰带你了解混凝土搅拌车的价格
  • 聚峰浅谈自上料搅拌车
  • 中科聚峰厂家告诉你如何使用小型混凝土搅拌机

全国服务热线

400-879-1999
新闻资讯 /news

3.5方搅拌机发动机运行错误有什么影响?

来源:http://www.zkhntjbc.com/ 日期:2021-10-07 浏览量:
概述:3 5方搅拌机的一些驾驶员认为发动机并不冷,因此发动机恒温器会自动移除,而冷却液只能从夜间循环中清除。发动机通常在高温条件下运行,因
3.5方搅拌机的一些驾驶员认为发动机并不冷,因此发动机恒温器会自动移除,而冷却液只能从夜间循环中清除。发动机通常在高温条件下运行,因为无法调节冷却强度。这会导致磨损并增加燃油消耗。实际上,高温对发动机有害。为了确保发动机的使用寿命,应将安装自动供料混合器的使用情况限制在环境温度范围内。
Some drivers of 3.5 square mixer think that the engine is not cold, so the engine thermostat will be removed automatically, and the coolant can only be removed from the night cycle. The engine usually runs at high temperature because the cooling intensity cannot be adjusted. This causes wear and increases fuel consumption. In fact, high temperature is harmful to the engine. In order to ensure the service life of the engine, the use of the automatic feed mixer should be limited to the ambient temperature range.
橡皮筋很好。如果皮带太松,不仅会拉伸并损坏皮带,还会缩短皮带的寿命,并且过大的压力会自动使搅拌机的发电机和泵轴负荷,从而损坏搅拌机。..为了满足技术要求,必须松开自动上料搅拌机的风扇皮带。建议的组装偏差为10到15毫米。
The rubber band is very good. If the belt is too loose, it will not only stretch and damage the belt, but also shorten the service life of the belt, and excessive pressure will automatically load the generator and pump shaft of the mixer, thus damaging the mixer In order to meet the technical requirements, the fan belt of the automatic feeding mixer must be loosened. The recommended assembly deviation is 10 to 15 mm.
许多驾驶员知道这辆车还处于起步阶段。同样,如果发动机转速过低,则可能由于打滑不好而损坏发动机。
Many drivers know that the car is still in its infancy. Similarly, if the engine speed is too low, the engine may be damaged due to poor slip.
但是,大多数人都知道自动热水混合器的油泵不能快速润滑光滑的表面润滑剂,因为它们的升温速度慢,它们在短时间内处于闲置状态。同时,由于热燃油雾化不足,已燃烧的燃油进入曲轴箱,冲刷气缸壁上的油膜并加速零件的磨损。因此,在启动自润滑发动机的几秒钟内,有必要改善怠速加热并提高高温条件下的发动机滑移率。
However, most people know that the oil pump of the automatic hot water mixer can not quickly lubricate the smooth surface lubricant because their heating speed is slow and they are idle for a short time. At the same time, due to insufficient atomization of hot fuel, the burned fuel enters the crankcase, washes the oil film on the cylinder wall and accelerates the wear of parts. Therefore, within a few seconds of starting the self-lubricating engine, it is necessary to improve the idle heating and increase the engine slip rate under high temperature conditions.

截屏,微信识别二维码

微信号:

点击微信号复制,添加好友

 打开微信